Exactly How to Replace a Tub Yourself: Removing and Replacing.
Exactly How to Replace a Tub Yourself: Removing and Replacing.
Blog Article
Here below you can find a good deal of worthwhile guidance in regards to How to Install a Bathtub.
Setting up a tub isn't specifically rocket science, however it does need solid plumbing, carpentry, as well as often, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably tough job. If the old tub is conveniently accessible, the project can move easily; if you have to open a wall to eliminate the old tub as well as place the brand-new bathtub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly need a helper to move out the old tub as well as embeded in the brand-new one. Make certain you have qualified yourself for the job and are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed project, it is far better to take into consideration using one before you begin. Chances are you might require a specialist plumber to make tube links.
This post will aid you set up a new bathtub in your bathroom if you have currently acquired a brand-new tub and don't require to transform the plan of your previous water system pipes.
Your tools and product checklist ought to comprise the following:
Planning for the Setup
Firstly, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make certain that if the tap features a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain any kind of water remaining in the system. The process of getting rid of the existing faucets can be quite troublesome as a result of the restricted gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a towel all set for the remaining water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming during this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Before proceeding to fit the brand-new faucets, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Setting up the Bath tub
Making use of the two wooden boards under its feet, put the bath tub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bathtub up until the level checks out degree.
To mount taps, fit the bottom of the furthest versatile tap port to the ideal supply pipeline by making a compression sign up with; then do the same for the other tap.
Turn on the water and also examine all joints and also brand-new pipework for leakages and also tighten them if needed. Load the tub and likewise check the overflow outlet and the regular electrical outlet for leakages.
Lastly, take care of the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bathtub should wait till the bath tub has actually been utilized at least when as this will certainly resolve it into its last setting.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making sure that the washers are in area in between the faucet and also the sink. Safeguard the faucet in place with the supplier offered backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the faucet ends first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom and the tiling, causing issues with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and also fittings. They are marketed in tubes and cartridges, as well as can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealant can split fairly very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a reader about How to Install a Bathtub Yourself, I assumed sharing that topic was a good idea. Make sure you take the opportunity to promote this post if you enjoyed it. We recognize the value of reading our article about Installing A Bathtub.
Schedule Services Report this page